How to connect the led light strip
The internal contact switch of the lamp port leads to the hot wire and the side contact zero wire, so that the safety factor will be improved. Draw the hot wire of the lamp mouth out of one end of the wire connection switch and the hot wire at the other end of the switch. Fix the lamp port, install LED, etc.
The wiring steps of the LED lamp are as follows: first, install the current limiting resistor on the negative pole of the power cord. Then separate the positive and negative lines of the LED lamp strip. Use a stripper to remove the positive wire of the LED lamp belt. Stripped positive line of LED lamp. This is shown in the following figure.
How to connect the led lamp strip? we can use this method of wiring at both ends, which is to short connect the two pins on both sides of the lamp holder of the LED. Then connect the internal power supply.
How to connect the led lamp
How to connect the led lamp into the wire at both ends: this is one of the more common connection methods in the early days. Because of the advantages of convenient wiring and other advantages, there are still some LED lamp manufacturers. Connect the two needles of the lamp holder short, and then connect them to the internal constant current power supply. This connection method can work normally as long as the traditional starter is removed.
The connection method of led lamp is as follows: tool / raw material: LED lamp. First of all, the length is determined and intercepted by integers. Random shortening will cause a unit not to shine. If you need a length of 5m, the lamp belt needs to be cut by 8m. If the positive and negative electrodes are connected in an insulated state, the lamp belt is not bright.
LED lights generally use 220V voltage, the connection method is as follows: the internal contact switch of the lamp port leads to the hot wire, the side contact zero wire, so the safety factor will be improved. Draw the hot wire of the lamp mouth out of one end of the wire connection switch and the hot wire at the other end of the switch. Fix the lamp port, install LED, etc.
Prepare a screwdriver and power cord. The wiring step of the LED lamp: first turn off the power supply, there will be a ballast with inductance inside the lamp rack, remove the ballast, and then unplug the starter. Connect the zero line and the hot wire to both ends of the lamp rack respectively. Put the lamp tube in the lamp rack, turn the lamp tube, and it will glow with electricity.
LED fluorescent lamps are generally connected to the wire at both ends, one end to the fire line and the other to the zero line. Note: there are two pins at both ends of the fluorescent lamp, and the two pins are connected.
How to connect the led lamp? (1) the wiring of the exposed lamp will concentrate the wire head in the middle as far as possible, and the exposed lamp extends around to install the lamp, which is convenient to connect the bus. at the same time, when a certain section of the line is burnt out, it can also ensure the normal operation of other lines.
Can LED line lights be seamlessly connected and installed?
LED Outdoor Waterproof Line Lamp with non-hidden Line at the bottom Generally installed with U-shaped buckle Compared with the structure of H-type Tibetan line Oh, it The installation is more convenient, but also seamless docking, direct joint, plug and play.
The outdoor installation of LED line lights pays more attention to the waterproof of the lamp strip and the firmness of the installation. Therefore, outdoor installation often uses the card slot fixed way, need to cut and connect the place, the method is the same as indoor installation, but need to be equipped with additional waterproof glue to consolidate the waterproof effect of the connection point.
Yes, as long as the output voltage of the transformer is consistent with the rated voltage of the lamp and the power of the transformer should be greater than or equal to the rated power of the lamp.
Pay attention to the connection distance of the LED light belt Generally speaking, the longest connection distance of 3528 series LED lamp belt is 20 meters, and the longest connection distance of 5050 series LED lamp belt is 15 meters. If the connection distance is exceeded, the LED lamp belt is easy to heat, and the service life of the LED lamp belt will be affected during use.
LED line lamp: emitting light source. DC12V drive power supply: convert AC220V power into safe DC voltage DC12V. Multi-strand copper cord 0.75mm: connect bending lamp strip. Glass glue: fixed line lamp.
According to different requirements, the product has 12V, 24V, etc., and the length has 30CM, 60CM, 90CM, 120CM and so on. Can also be customized according to customer needs of different specifications of line lights.
