How to use Xiaomi sensor lamp
1. First, plug its millet full moon lamp into the power supply. Secondly, touch the sensor night light with its hand. Then the light will come on.
2. First of all, the setting of Mijia desk lamp needs to use “Mijia” APP. You can enter Mijia in the application mall and search for download and installation. If you are using a Xiaomi mobile phone, the general system is pre-installed with Mijia app, you can open it directly.
3. The switch setting of the induction lamp needs to be calibrated in time at the beginning, and then after the gesture operation is completed, there is a physical button on its side that can be adjusted and turned on directly.
4. Xiaomi’s human body sensor has no way to control the lamp, only Xiao Ai can control the lamp.
5. This millet desk lamp needs to be controlled by mobile phone. You can download it on your mobile phone. After each APP is connected, it can be controlled by mobile phone, and it can be turned on and off by voice. If you have a young classmate on your phone, just ask him to turn the light on and off, and he can help you.
Induction door failure
(4) check whether the induction automatic door is equipped with safety light, because the dust cover on the light receiver of the safety light will also cause misoperation, so that the automatic door owner control mistakenly thinks that there is an object in the middle of the door, so as to stop closing the door. 2 automatic door response is slow (1) the detection range of the sensor probe is too small.
When a sound is issued, the message indicates that the operation is successful, the green light is on, and the lock is unlocked. 2 sounds indicate that the management card is not performing correctly and the red light flashes 2 times. The sound of 3 sounds indicates that there is an error in reading and writing data, and the red light flashes 3 times. 4 sounds and the address is wrong, indicating that the address of the card does not match the address of the door lock.
Maybe it’s plugged in, but there’s no power. Or it could be that the door is stuck. In addition, it is caused by the controller crash. For this phenomenon, you should first check whether the indicator light of the power supply is on, and use your hand to pull the door to see if it is stuck.
Fault phenomena such as jitter. The method of testing the fault of the induction door the method of testing the fault of the induction door, first cut off the power supply and open the door by hand: make sure there is no garbage in the track. If there is a lock on the lower part of the door leaf, make sure that the lock is not loose. Confirm that the pendulum stopper is in contact with the guide rail and keyhole due to damage or loosening.
The failure of the induction door may be caused by the damage of the sensor, the door signal is always input to the induction door controller, and the induction door remote control or mode switch switch may be adjusted to the open state. if an access control system is installed, the relay of the access control system may be damaged.
The fault treatment method of the Thomas automatic sensing door is as follows: check whether the mobile door has the phenomenon of mopping the floor, if there is this phenomenon, the door is very difficult to start, and the main controller will mistakenly think that there is an obstacle and run the protective effect, so that the door leaves stop running.
Introduction to the mode and installation method of led infrared induction lamp
Infrared induction lamp is divided into ceiling type, embedded type, E27/E26 screw bubble type. The installation mode of the existing building transformation: replace the lamps and lanterns, the original switch circuit is short connected (or placed in the open state), and the lamps can be connected to electricity. The installation mode of the new building: there is no need to arrange switches and pipelines on the wall, just connect the lamps and lanterns directly.
When this product is powered on for the first time, the continuous light will be on three times, indicating that it is normal, but it will not turn on normally during the day or when the light is strong, and the light can be turned on automatically when the light is dim at night. Such as in the daytime, use black cloth to cover the infrared probe lens, after ten seconds (do not let it pass through the light) can also try its light to work.
Because the sensor is infrared, the device should be facing outward and the led light should be put down. If no heat source is detected, the led sensor lamp will not be activated. If the sensor detects the heat source of the human body, it will glow for about 15 seconds, and if there is no heat source, it will automatically go out. The above is the installation method of wardrobe induction lamp.
Such as in the daytime, use black cloth to cover the infrared probe lens, after ten seconds (do not let it pass through the light) can also try its light to work.
Start the illuminance 10LX. A variety of installation methods. Infrared induction lamp principle infrared human induction lamp has the characteristics of super energy saving, intelligent control, integration of light source and control module, etc., completely replacing the traditional corridor human induction lamp, corridor acousto-optic control light and touch switch light.
The induction switch can be divided into 86 type induction switch and suction top type induction switch. Type 86 induction switch is the same size as the traditional mechanical wall switch and can directly replace the original wall switch. The installation method of suction top induction switch is more or less the same, take BR-306C as an example. Make a round hole with a diameter of 60mm in the ceiling.
How to use the fishing headlamp sensor light
1. Installation. First, install the fishing headlamp sensor lamp to the desired location according to the installation instructions, and then connect the power supply to the lamp to adjust the appropriate angle. Set up. Set the lamps and lanterns according to their own needs. For some fishing headlamp sensor lights, you can use a manual switch or adjust the light brightness as needed.
2. Because the induction range of the left and right sides of the switch is larger than that of the upper and lower sides, when installing the switch, the positive axis should be perpendicular to the direction of the human walking channel as far as possible, so that the best induction effect can be achieved.
3. That kind of fish is a deep-water fish that lives in the dark deep sea. That small lamp is used to attract other small fish and other creatures, which is the bait. It’s called the mackerel.
How to use the 2020 Maiteng 330 deluxe automatic sensing headlamp
1. What is the use method of Volkswagen Maiteng automatic headlights, and how to turn on Maiteng automatic headlights? In fact, the steps are simple and not too difficult, but first you have to find the button that controls the headlights. There is an AUTO position on the light button, and this is the automatic mode.
2. Open the door on this side of Maiteng’s cab. Step on Mai Teng’s brake pedal. Press the start button of Maiteng to start the engine. The dashboard lit up, proving that Maiteng’s engine had started. Turn the Mai Teng headlight switch to the AUTO position to complete the operation.
3. The shift lever on the left side of the Maiteng steering wheel is used to control the basic light switching, the outer control far and near light switching, the inside control turn signal and parking lights. The switch of the light is controlled by the left shift lever, where the stop light uses the same logic as the turn signal. After parking is turned off, you can pull the gearshift lever up and down to turn on the stop light.
4. The activation method of adaptive far and near light setting for Maiteng matrix headlamp. The headlamp is placed in the AUTO file, the intelligent high beam control system is on, and the speed is higher than 40km/h. When the conditional headlamp is not placed in the AUTO file, the intelligent high beam control system can be released.
5, we usually talk about automatic headlights, as long as the car sensor, feel the intensity of the outside light, it will automatically turn on, turn on or turn off the lights in time. The main function of headlights is to illuminate the direction ahead. How to use automatic headlights? it is effective when we set the automatic switch to (AUTO block).
6. Open mode: adjust to automatic position. The adaptive headlamp can adjust the height of the headlamp according to the angle and speed of the turn. When the vehicle turns to a corner, the adaptive headlight will be turned on automatically. And only if the speed does not exceed the 70km/h can it work properly.
How to adjust the sensor light?
1. Adjust the human body induction lamp: because the induction range of the left and right sides of the switch is larger than that of the upper and lower sides, when installing the switch, the positive axis should be perpendicular to the direction of the human walking channel as far as possible, so that the best induction effect can be achieved.
2. The adjustment steps of the automatic headlight sensor are too sensitive: 1. Start the vehicle to power the whole vehicle; roll the wheel on the left dashboard, and the sensing distance of the headlights will change accordingly. The higher the sensitivity, the darker the headlamp and the lower the sensitivity. Only the cars near the other side will get dark.
3, wiring, one of the lamp body power cord is connected with the fire wire with a connecting particle, and the other is connected with the zero wire. After the connection, the wire grain is pulled hard and does not fall off; install the light bulb, glass or back cover. It can be electrified for trial.
4. First of all, because the induction range of the left and right sides of the switch is larger than that of the upper and lower sides, when installing the switch. Secondly, the positive axis should be perpendicular to the direction of people’s walking passage as far as possible. Finally, this can achieve the best sensing effect.
5. The sensitivity method of induction lamp adjustment of Sidon staircase is as follows. First turn on the switch of the voice control light, in which there is a black cylinder, which is connected in series with an adjustable resistor between the microphone and the circuit to effectively adjust the sensitivity according to your own needs. Put a thicker sticker on the sensor switch, which reduces his sensitivity.
