Led flat panel lamp installation, the method is actually this simple 8 steps

1. There are three installation methods of LED flat panel lamp: embedded, ceiling and hanging, so we must first determine what kind of installation method. Prepare sharp-nosed pliers, solder, AB glue, multimeter, etc.

2, shops, kitchen rooms and other occasions, is also the most common installation method, first remove a ceiling, put the driver of the LED panel lamp on the next ceiling, and then connect the power cord, and then put the board lamp above, the installation method is relatively simple.

3. The first method is the simplest and most common installation method: first, take a ceiling, put the driver of the LED panel light on the next ceiling, connect the power cord, and then put the board light on it. The second method is hoisting, to use the cable.

What process is required for led lamp assembly?

1. The assembly process of led lamp includes: plug-in, tin dipping, foot cutting, testing, assembly, aging and packaging.

2. When installing, replace the original fluorescent lamp with LED fluorescent lamp, remove the ballast and starter, and add 220V AC power directly to both ends of LED fluorescent lamp.

3. The installation method of Led lanterns choose the location where led lanterns should be installed. The recommended installation height is that the bottom of led lanterns is more than 4 meters from the ground. After the position is selected, punch a hole in the lamp pole and pass the cable from the hole position to the connection position at the bottom of the lamp post.

How to install LED flat panel lights

1, shops, kitchen rooms and other occasions, is also the most common installation method, first remove a ceiling, put the driver of the LED panel lamp on the next ceiling, and then connect the power cord, and then put the board lamp above, the installation method is relatively simple.

2. There are three installation methods of LED flat panel lamp: embedded, ceiling and hanging, so we should first determine what kind of installation method. Prepare sharp-nosed pliers, solder, AB glue, multimeter, etc.

3. The first method is the simplest and most common installation method: first, take a ceiling, put the driver of the LED panel light on the next ceiling, connect the power cord, and then put the board light on it. The second method is hoisting, to use the cable.

4. Plug the LED lamp board into the wire interface of the ballast and place the ballast in the ceiling. Finally, press the flat lamp buckle vertically, put the flat lamp into the installation hole, and the whole lamp will be installed. After installation, people turn on the power test to see if the led flat panel lamp can be used normally, and if not, it should be adjusted.

5. installation method: ceiling lamp: it can be fixed directly with screws. Embedded LED lamp: step 1: open the hole, and then jam the lamp buckle. Step 2: because the specific situation of each lamp is different. Next, the specific operation should be carried out in accordance with the instructions attached to the LED lamp.

6. The first method is the office, which is the simplest and most common installation method: first, take a ceiling, put the driver of the LED panel light on the next ceiling, connect the power cord, and then put the board light on it. The second method is hoisting, to use the cable.

Diagram of how to install flat panel lamp

The common installation methods of led flat panel lamps are embedded, ceiling and hanging type. First of all, what kind of installation mode should be determined according to the installation location and the style of the lamps and lanterns. Led panel lamp installation step 2 get the installation tools ready, such as sharp-nosed pliers, solder, AB glue, multimeter and so on.

Embedded installation method: suitable for integrated ceiling installation, this installation method is often used in offices, stores, kitchens and other occasions, but also the most common installation method, first remove a ceiling. The following figure connects the adapter of the flat panel lamp to the wire. As shown in the picture, the male and female interfaces of the flat lights can be docked.

There are three installation methods of LED flat panel lamp: embedded, ceiling and hanging, so we must first determine what kind of installation method. Prepare sharp-nosed pliers, solder, AB glue, multimeter, etc.

Led flat panel lamp installation method 1 there are embedded LED flat panel lamp, ceiling type, hanging three installation methods, the first to determine which installation mode is. 2, prepare sharp nose pliers, welding, AB glue, multimeter, etc.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *